OWNER’S
MANUAL
MODEL NO.
WB80042F
THE FINISHING TOUCH
42” FINISH CUT MOWER SELF PROPELLED
WALK BEHIND
Read and follow all Safety
Rules and Instructions
before operating this
equipment.
Assembly
Operation
Service and Adjustment
Repair Parts
Rev. 12.18.2002
1602 CORPORATE DRIVE, P.O. BOX 67, WARRENSBURG, MISSOURI 64093
PHONE (660) 747-8183 FAX (660) 747-8650
Made In The
Manufacturing quality lawn care equipment since 1945
USA
ONWB842
SERVICE AND ADJUSTMENTS
Stop engine, let all moving parts come to a complete stop. Disconnect spark plug.
BLADE SPINDLE
BELT
TRANSMISSION BELT
BLADE DRIVE BELT
BELTS CONFIGURATION
BLADE SPINDLE BELT REPLACEMENT
REMOVAL
•
Stop engine, let all moving parts come to a complete stop. Disconnect spark
plug.
Remove belt cover.
Remove Blade Drive Belt. (See Blade Drive Belt replacement.)
Pull tension idler away from Blade Spindle Belt to relieve tension.
•
•
•
•
Remove belt.
INSTALLATION
•
•
•
Pull tension idler away from belt.
Install belt according to above configuration.
Install Blade Drive Belt as shown.
•
Install belt cover and tighten hardware.
BLADE DRIVE BELT REPLACEMENT
REMOVAL
•
Stop engine, let all moving parts come to a complete stop. Disconnect spark
plug.
•
Disengage all blade controls by releasing the bails.
Remove belt cover.
Rotate belt off pulleys and pull belt through motor belt guide.
•
•
INSTALLATION
•
•
Route belt as shown.
Adjust engage idler tension. Belt should be snug during engagement of blade
latch. Too much tension will not allow the blade latch to function properly.
Tighten nuts on blade engage cable when finished.
Install belt cover and tighten hardware.
•
•
WHEEL DRIVE BELT REPLACEMENT
REMOVAL
•
Stop engine, let all moving parts come to a complete stop. Disconnect spark
plug.
Remove belt cover.
Remove Blade Drive Belt, (See “Blade Drive Belt replacement”)
Locate belt guide for wheel drive belt and loosen.
•
•
•
•
Remove wheel drive belt.
INSTALLATION
•
•
•
Install belt as shown.
Adjust belt guide snug against motor pulley and back off ?”.
Tighten belt guide hardware.
•
•
Install Blade Drive Belt (see “Blade Drive Belt installation”).
Install belt cover and tighten hardware.
Check for loosened bolts, nuts,
springs, etc. often. Replace
filters, spark plugs as needed.
Keep blades in good working
order.
Adjust Nuts
WHEEL BRAKE ADJUSTMENT
Adjustment may be necessary if the unit does not stay in position on a hill with the
operator bails released, or if the brake drags while in neutral with the “GROUND
CONTROL” bail engaged.
PROCEDURE
•
Stop engine, let all moving parts come to a complete stop. Disconnect spark
plug.
•
•
Release “GROUND CONTROL” bail.
Adjust nuts forward or backward. When the “GROUND CONTROL” bail is
disengaged there should be constant tension on the brake arm.
All tension should be off brake arm when “GRO UND CONTROL” bail is
•
engaged.
•
Tighten adjustment nut when finished and re -attach spring, if necessary.
WHEEL DRIVE BELT ADJUSTMENT
Adjustment may be necessary if loss of traction occurs due to belt slippage.
PROCEDURE
•
•
Adjust “GROUND CONTROL” cable in or out to achieve maximum traction.
Too much tension will not allow the “GROUND CONTROL” bail to fully
activate.
•
•
Too little tension will allow the belt to slip, resulting in loss of traction.
“GROUND CONTROL” bail should fully close against handlebars when
functioning properly.
REPLACEMENT PARTS
When ordering painted parts, please indicate with corresponding letters: C = Red Parts;
TK = Textured Black Parts (ex. 4207TK, 4237C)
Item #
Description
Part #
Item #
Description
Part #
1
2
Motor Base
Wire Link
4270
BRS6H
46
47
Tension Spring
1/2 x 1 9/16 Shoulder Bolt
682S
NB220
3
4
Link Spring
5/16-18 Serrated Flange Nut
T2SM
NB170
48
49
5/16 SAE Washer
3/8-16 Grade 2 Nut
NB275
NB212
5
6
5/16-18 x 21/2 Grade 5 Bolt
Shift Linkage
NB138
4282
50
51
5/16-18 Nylock Nut
Tension Idler Kit
NB181
4263
7
8
Blade Driver Housing
Brake Spring
B99
BT297
52
53
Blade Engage Pulley
Blade Drive Belt
7509
4220
9
10
Brake Pad
Blade Engage Idler
BP370
4262
54
55
Blade Spindle Belt
Wheel Drive Belt
4219
2414
11
12
1/2 -13 Nut
Brake Pad Clip
NB213Z
BP370S
56
57
Transmission Belt Guide
1/4-20 Flange Nut
2451
NB524
13
14
5/16 Flat Washer
3/8 -16 2-way Locknut
NB556
NB280
58
59
Blade Drive Belt Guide
8HP B&S Engine
4234
N/A
15
16
5" Chain Links
3/8-16 x 2 Grade 2 bolt
AS080
NB231
60
61
Upper Engine Spacer
1/4 x 1/2 Key Stock
689L
4258
17
18
1/2-13 x 5 Grade 5 bolt
Blade Engage Idler Kit
NB155
4280
62
63
Upper Engine Pulley
Lower Engine Spacers
2411
BB105SL
19
20
1/8 x 1 Cotter Pin
Center & Left Blade Driver Kit
NB126
9080
64
65
1/4 x 1 Key Stock
Lower Engine Pulleey
9031
688
21
22
Blade Bearing
Center & Left Blade Shaft
B98
9075
66
67
Belleville Washer
7/16-20 x 1 1/2 Grade 5 Bolt
699
NB637
23
24
Washer
1/4-20 x 1 Grade 5 Bolt
B98W
NB250
68
69
Height Adjust Arm
Front / Rear Torsion Connector
4275
4235
25
26
1/4-20 Nylock Nut
15" Blade
NB180
4221
70
71
Front Torsion Bar
Rear Torsion Bar
4233
4236
27
28
Serrated Belleville Washer
3/8 - 24 x 1 1/4 Grade 5 Bolt
NB607
NB166
72
73
3/4 x 18 GA Washer
5/16-18 x 3/4 Serrated Flange Bolt
NB179
NB596
29
30
Blade Mounting Plate
3/8-24 2 Way Lock Nut
9008
NB216
74
75
Plastic Belt Cover
3/8-16 x 3 Eye Bolt
4257
NB635
31
32
3/8-24 x 1 Grade 5 Bolt
Lower Blade Pulley
NB238N
B4104
76
77
3/8-16 Nylock Nut
Front Tire & Wheel
NB182
4218
33
Pulley Spacer
6104RS
B104
78
79
Caster
5/8 x 10 GA Washer
4266
NB149
34 Upper Blade Pulley (Center & Left Only)
35
36
3/4-16 2 Way Lock Nut
Right Blade Shaft
NB629
9077
80
81
5/8 Flanged Bearing
Grass Chute
F157B
4261
37
38
Right Blade Driver Kit
Transmission Idler Pulley
9079
B27
82
83
5/16-18 x 8 1/2 Grade 2 Bolt
Grass Chute Spring
NB136
CH5S
39
40
Transmission Idler
3/8-16 x 1 1/2 Grade 5 Bolt
4276
NB107
84
85
Plastic Roller
5/16-18 x 5 1/2 Grade 5 Bolt
AS001
NB521
41
42
1/2-13 x 2 1/2 Grade 5 Bolt
3/8 SAE Washer
NB588
NB272
86
87
1/2 x 14 GA Washer
5/16-18 x 4 Carriage Bolt
NB177
NB101
43
44
Transmission Idler Kit
Tension Idler Pulley
4281
B527
88
89
Hanger Bracket
1/2-13 2 Way Jam Lock Nut
4216
NB121
45
Tension Idler
6681
90
Rear Tire & Wheel
4217
REPLACEMENT PARTS
When ordering painted parts, please indicate with corresponding letters: C = Red Parts;
TK = Textured Black Parts (ex. 4207TK, 4237C)
Item # Description
Part #
91
92
Sway Bar
3/16 x 1 1/2 Keystock
4207
2434
93
94
3/4 E-Clip
3/4 x 10 GA Washer
NB621
NB184
95
96
5/16-18 x 1/2 Set Screw
4 Speed Transmission
NB192
4256
97
98
1/4 SAE Washer
Shift Link
NB274
4223
99
100
1/4-28 x 3/4 Grade 5 Bolt
Brake Mount
NB620
4273
101
102
Brake Mount Kit
Transaxle Brake Pivot
4271
4247
103
104
Transaxle Brake Link
1/4-20 x 3/4 Eye Bolt
4264
V139EB
105
106
5/16-18 x 1 Grade 5 Bolt
Gear Shift Spring
NB501
TR148S
107
108
Rear Cover
5/16-18 x 1 1/4 Serr. Flange Bolt
4299
NB253
109
110
Thrust Bearing
Plastic Knob
T151
4857
111
112
Crank Handle
Transmission Pulley
4274
2410
113
114
3/8 Hardened Washer
Wiring Harness
NB196
4268
115
116
Throttle Control
1/4-20 x 1 1/2 Grade 2 Bolt
4226
NB104
117
118
1/4-20 x 1/2 Self-tapping Bolt
ON/OFF Key Switch
NB114
KSM
119
120
Throttle Console
Gear Shifter
4292
4260
121
122
Blade Engage Latch
1/4-20 x 2 1/2 Grade 5 Serr. Flange Bolt
4295
NB208
123
124
Operator Handle
Transmission Cable
2402
2432
125
126
Operator Presence Bail (Upper)
Ground Control Bail (Lower)
4294
4291
127
128
3/16 x 1 Roll Pin
Belt Guide
NB123
4283
129
130
Oil Drain Cap
Oil Drain Valve
AS123
AS122
131
132
5/16-18 x 1 1/2 Serr. Flange Bolt
3/16 x 3/4 # 9 Woodruff Keystock
NB254
NB638
133
134
Frame
Deck
4269
4250
THE FINISHING TOUCH
42” FINISH CUT MOWER SELF PROPELLED
WALK BEHIND
Each cutter has its own model number. Each engine has its
own model number. The model number for the cutter will be
found on the right hand side of the motor base. The model
number for the engine will be found on the top of the blower
fan housing.
All cutter parts listed herein may be ordered directly from
Swisher Mower & Machine Co. Inc. or your nearest Swisher
dealer.
OWNER’S
MANUAL
All engine parts may be ordered from the nearest dealer of the
engine supplied with your cutter.
MODEL NO.
WB80042F
WHEN ORDERING PARTS, PLEASE HAVE THE
FOLLOWING INFORMATION AVAILABLE:
* PRODUCT – FINISHING TOUCH
* SERIAL NUMBER - _______________
* MODEL NUMBER - _______________
* ENGINE MODEL NUMBER - _______________
TYPE - _______________
* PART NUMBER
* PART DESCRIPTION
TELEPHONE - 1-800-222-8183
FAX - 1-660-747-8650
SWISHER MOWER & MACHINE CO. INC.
1602 CORPORATE DRIVE P.O. BOX 67
WARRENSBURG, MO 64093
SWISHER MOWER & MACHINE CO. INC.
PRINTED IN U.S.A.
|